gif
gif
gif

LOCATE  |  ABOUT  |  FAQ's - POLICIES  |  REVIEWS  |  PRIVACY  | 

shopping cart

gif
gif
gif gif gif  
gif gif gif gif gif

 

DRIVELINE DISCONNECT PARTS

 You are on page 2 -  Go to page 1

Since 1985 we have supplied repair parts for both the Remco Driveline Disconnect and also the Lube Pump systems. We also assemble our own Driveline Disconnect kits and have been a factory direct dealer, installation, service, parts and warranty center. We offer complete turn-key installations and repair at our facility in Yuma AZ. read more

NOTE: All Shifter Housings use the same components. The actual Housing is vehicle-specific.

INFO: Mouse-Over the illustration at bottom of page for Coupler Housing parts identification.


Remco Wescon, cable anchor/swivel

MFG# 11000110

qty:

Remco Shift Fork (Horse Bit) pivot arms. Top is the Regular arm, middle is the dual or long arm and the bottom is the special L-arm. (sold as single arm)

MFG# regular 11000858 long 11001858 L-shaped 11001857

qty:

Cable assembly for coupler Standard cable for the coupler, original Remco cable 10' long. Can and should be cut to required length. Also "REMEMBER", your differential moves forward and backwards in relation to the frame and also frame lifts that allow your axle to drop away from the frame so take this into consideration when calculating your required cable length. Do not "coil" this cable for shorter length requirements in your vehicle (you will be sorry if you do)

MFG# 40000138

qty:

Disconnect bearing Remco Driveshaft Disconnect Bearing. This bearing is for the second generation coupler yoke and tube stub. Width is .812

MFG# 40000002

qty:

Detent spring and ball kit Detent Spring and Ball Kit. Two springs and balls.

MFG# kit 40000005/3

qty:

Coupler Yoke w/bearing Coupler Yoke. Comes w/bearing and retainer. These yokes are available in 1310, 1350 and 1410 series. This yoke must be used with the second generation tube stub. This yoke is double keyed.

NOT AVAILABLE UNTIL FURTHER NOTICE

 
qty:

Disconnect sleeve Disconnect Shift Sleeve. This sleeve is for double key couplers. We do not supply single key components.

NOT AVAILABLE UNTIL FURTHER NOTICE

 
qty:

Tube stub Disconnect Tube Stub. These stubs are available in 2-1/2", 2-3/4", 3" and 3-1/2" tube sizes. All are for .065 wall tubing (press fit). Custom diameter machining is available. These stubs are for double key couplers and must be used with the second generation coupler yoke. We do not supply single key components.

NOT AVAILABLE UNTIL FURTHER NOTICE

 
qty:

Remco Driveline Disconnect small parts kit. Contains 3 rubber backed cable clamps, cable anchor clamp, anchor clamp 1/4" bolt, nut and lock-washer, cable mounting bracket, mounting bracket screws and the cable wescon swivel. 12 pieces in-all. (Kit sold as pictured)

MFG# 10000066

qty:

 You are on page 2 -  Go to page 1 

 
 
Page Last Updated 12/01/2014
Contents subject to change without notice
 
 

 |  Contact  |  About  |  Locate  |  Returns  |  FAQ's & Policies  |  Privacy  |  Terms  |  Reviews  |

Positive SSL on a transparent background

website security

   

Copyright © 1985-2014 Southwest Driveline Service. All rights reserved

All trademarks mentioned herein belong to their respective owners
SW Driveline Service is a dealer for Remco and Superior Driveline. We are an
individual entity and have no legal relationship with either manufacturer.
website design by, the old man